How To Change Belt On Ge Dbsr463eg2ww Dryer

Drum Bearing Slide - White

PartSelect #: PS755842

Manufacturer #: WE1M504

This authentic, white Drum Bearing Slide, too known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer'southward front drum slide to allow for ...

$nine.95

In Stock

Social club inside the side by side 10 hrs and your part ships today!

Drum Bearing Slide - Green – Part Number: WE1M1067

Drum Begetting Slide - Green

PartSelect #: PS6447706

Manufacturer #: WE1M1067

This original equipment manufacturer Drum Bearing Slide is a plastic, greenish, easy-to-install part for your dryer. It replaces the dryer'south front pulsate slide to allow for easier movement. Y'all'll know if...

$6.70

In Stock

Order inside the next 10 hrs and your office ships today!

Front Drum Bearing – Part Number: WE3M26

Front Pulsate Bearing

PartSelect #: PS960316

Manufacturer #: WE3M26

This Front Pulsate Bearing (Top Bearing, Dryer Drum Front end Back up Bearing, Drum Support Bearing, Dryer Drum Glide Bearing) holds the drum bearing and slides for the drum to plough on. The front drum bearin...

$45.50

In Stock

Order within the next 10 hrs and your part ships today!

Control Knob and Clip - White

PartSelect #: PS9493075

Manufacturer #: WE01X20378

This set (Knob and Clip Assembly, Command Knob, Dryer Control Knob) allows you to supersede the knob on your timer if it is damaged or missing. The plastic knob tin break around its shaft, or the retain...

$31.82

In Stock

Lodge within the next 10 hrs and your part ships today!

Timer Knob

PartSelect #: PS1482197

Manufacturer #: WE1M654

This timer knob is used to set the dryer cycle past advancing the timer. The plastic can go breakable with age and crevice where it attaches to the timer shaft. You will need to replace this part if it ...

$30.78

In Stock

Order within the side by side 10 hrs and your part ships today!

Drive Belt

PartSelect #: PS1766009

Manufacturer #: WE12M29

This Bulldoze Belt is 89.v" long and comes in blackness, featuring four ribs on the inside for a improve grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and th...

$35.56

In Stock

Order inside the adjacent 10 hrs and your part ships today!

D-Shaped Knob Insert Clip

PartSelect #: PS267091

Manufacturer #: WE1X980

This clip ensures that the knob is securely fastened to the control shaft, allowing you to properly select the right time and setting for your dryer. If your dryer will non commencement or shut off, the ti...

$viii.30

In Stock

Order within the next 10 hrs and your part ships today!

Rotary Start Switch

PartSelect #: PS3487203

Manufacturer #: WE4M519

This replacement start switch is a 18-carat OEM part for your dryer. If your dryer volition non beginning or close off, you lot may need to replace this office. For this repair you will need a number ii Phillips screw...

$14.56

In Stock

Order within the adjacent 10 hrs and your part ships today!

FELT TRAP DUCT

PartSelect #: PS12722961

Manufacturer #: WE09X27634

May differ in appearance but functions same as original.

$8.xxx

In Stock

Society inside the next 10 hrs and your part ships today!

Rear Drum Bearing Kit – Part Number: WE25M40

Rear Pulsate Bearing Kit

PartSelect #: PS267529

Manufacturer #: WE25M40

This rear drum bearing kit includes a shaft, ground strap, bearing, seven screws, and installation instructions. The bearing plate comes with a slot in it for the footing strap. This part helps keep yo...

$87.98

In Stock

Guild inside the adjacent 10 hrs and your role ships today!

We're pitiful, but our Q&A experts are temporarily unavailable.
Please check back afterwards if y'all yet oasis't found the answer yous need.

Due to over loading of the dryer the drum ruined the slides and was making a bad dissonance due to plastic rubbing plastic

It was pretty easy. After already taking autonomously the dryer to install a new belt I knew exactly my plan of activeness. I removed the two screws that hold the height panel of the dryer to the front panel. I then removed the acme console and removed the screws that hold the front end to each side console. I than pulled the front end abroad from the chiffonier and pulsate. I put the new slides in identify and installed a new felt strip. I put it back together and that was that. Very like shooting fish in a barrel.

Parts Used:

Matthew from Plainfield, IL
Difficulty Level:

Really Easy
Total Repair Time:

fifteen - xxx mins

748 of 844 people plant this teaching helpful.

Was this instruction helpful to yous?

Give thanks you for voting!

Dryer was squeeling when running.

I removed the two screws at the front above the drum opening (with the dryer door open up). The height panel then lifts off. I removed the spiral at each side that holds the front panel to the side panels, tilted the front console frontwards, which disengages the forepart of the drum from the forepart drum glide bearing. I then lifted the front end console slightly, unhooking the bottom of the console from the dryer base, and swung the front console aside. I removed the existing top pulsate bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the quondam felt strip, and pressed the new ane in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the begetting guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the pinnacle, and replaced the front end top console screws.

Parts Used: